Before the installation of doors and windows, the door and window frames of different specifications should be moved to the corresponding holes and placed vertically. If it is found that the protective film falls off, the protective film should be subsidized, because the protective film is the last protection of the rolling shutter door, and it is difficult to protect the doors and windows without the protective film.

在安裝將窗框放入洞口，使其上下框中線應與洞口上的安裝中線對齊，并在框的四周及中蜒處用水?；驂|塊塞緊作臨時固定，然后按設計困紙要求確定窗框在洞口罐體厚度方向的安裝位置，以及安裝高度，并慢慢地進行調整。

During installation, put the window frame into the hole so that the center line of the upper and lower frames is aligned with the installation center line of the hole, and plug the frame around and in the middle with water mold or cushion block for temporary fixation, then determine the installation position and installation height of the window frame in the thickness direction of the tank body at the hole according to the design requirements, and adjust it slowly.

調整的方法就是高度人或拉出墊在框與精體之間的木模，使窗框抬高或降低，以達到所需的位置。

The method of adjustment is to raise or lower the window frame by pulling out the wooden mold between the frame and the body, so as to reach the required position.

在將窗框調整到位后，先固定兩點，應選窗框的兩對角點行固定，然后再次對窗框的垂直度、水平度及直角度進行調整，使其偏差小于規定的要求后，再將其他螺釘分別固定牢固即可。

After the window frame is adjusted in place, two points shall be fixed first, and the two diagonal points of the window frame shall be fixed first, and then the perpendicularity, levelness and right angle of the window frame shall be adjusted again, so that the deviation is less than the specified requirements, and then other screws shall be fixed firmly.

門的安裝與窗的安裝各有不同，門的安裝應在地面裝飾工程施工前進行。應根據設計圖紙及門扇的開啟方向，確定門框的安裝位置，并把門裝入洞口，安裝時應采取防止門框變形的措施，無下框平開門應使豎框的下邊低于地面標高線，其高度差應不小子30mm。

The installation of door is different from that of window. The installation of door should be carried out before the construction of ground decoration engineering. The installation position of the door frame shall be determined according to the design drawings and the opening direction of the door leaf, and the door shall be installed into the hole. During the installation, measures shall be taken to prevent the deformation of the door frame. For the flat door without lower frame, the lower edge of the vertical frame shall be lower than the ground elevation, and the height difference shall not be less than 30mm.

也即豎框應少理入地停以下30mm。而帶下框的平開門或維拉門應使下框低于地商標高線，其高度差宜為10mm，也即橫下框應少埋入地坪以下10mm。

That is to say, the vertical frame should be at least 30mm below the ground stop. For the side hung door or sliding door with lower frame, the lower frame should be lower than the elevation of the ground mark, and the height difference should be 10 mm, that is, the horizontal lower frame should be buried at least 10 mm below the ground level.

然后，將上框的一個國定片固定在精體上，并用木模臨時定位，同時調整門框的水平度、垂直度和直角度，當所有尺寸都到位后，就將所有的固定螺釘全部固定到位。

Then, fix a national fixed piece of the upper frame on the fine body, and use the wood mold to temporarily position it. At the same time, adjust the levelness, perpendicularity and right angle of the door frame. When all the dimensions are in place, fix all the fixing screws in place.

當安裝連窗門時，門與窗應采用拼撞料拼簇，餅橙料下峭應固定在窗臺上。

When installing the door with windows, the doors and windows should be made of colliding materials, and the orange cake material should be fixed on the windowsill.